Pošlite nám e-mail: contact@stasgroup.com

STAS windsor & riva wooden rail

In addition to aluminum rails, STAS also offers wooden rails in 2 different models. The STAS windsor is elegant and warm where the STAS riva has a more robust look and feel. Two distinctive models, suitable for any interior! Both models are easy to use and each has a different profile for which fitting hooks are available.

Our wooden rails are made out of Ayous wood and are FSC and PEFC certificated. Ayous wood differs from other wood since it does not deform nor splinter, and perfectly suitable to repaint because of its smooth texture. Perfect wood for your picture hanging system! Can be mounted screwed, nailed and glued*.

Experience the pleasant warmth of wood in your interior!

* The bearing capacity of a glued rails is highly dependent on the surface, so care must be taken here. More information on how to best glue our wooden rails can be at the bottom of this page.

STAS wooden rail

Features STAS windsor:
Dimensions: 18 x 45 mm
Length: +/- 240 cm
Material: Ayous wood
Installation: wall mountable, not adjoining to ceiling
Weight capacity: 20 kg/m
Warranty: 5 years

Features STAS riva:
Dimensions: 17 x 45 mm
Length: +/- 240 cm
Material: Ayous wood
Installation: wall mountable, adjoining to ceiling
Weight capacity: 20 kg/m
Warranty: 5 years

STAS windsor & riva have their own collection of hooks, which can be combined with the existing hooks and cords from STAS:
STAS riva: HW50700
STAS windsor:
HW10200 white
HW30200 alu
HW60200 gold

The following hooks and cords can be used in combination with this system:
STAS smartspring on STAS perlon cord with loop (can be loaded up to max. 4 kg)
STAS zipper on STAS perlon cord with loop (can be loaded up to max. 15 kg)
STAS zipper on STAS steel cable with loop (can be loaded up to max. 20 kg)

Download:

Installation manual | Productinfo


Mounting videos : STAS riva mounting with screws and glue



Mounting videos : STAS windsor mounting with screws and glue


5-Step Plan for glueing the STAS riva & STAS windsor

Step 1: Assess the surface

When glueing the STAS wooden rails it’s very important that the surface is well fixed and firm. This goes especially for wall paper. The wall paper must have been applied tightly and evenly to allow the STAS wooden rails to adhere as well as possible.

Step 2: Pick the right glue.

We recommend a glue that is especially designed to offer a very good adhesion on wooden surfaces. We advise you to go see your local DIY store for further recommendations.

Step 3: Pretreatment

Make sure that the surface and the STAS wooden rails are clean, dry, dust- and grease free before you start glueing.

Step 4: Glueing

The glue can best be applied in strokes (so don’t cover the whole rails in glue). Once the glue is applied you can place the STAS wooden rails on its surface (make sure it’s level!). The STAS wooden rails can at this point still be adjusted. When the rails are in the right place you can exert pressure so that the STAS wooden rails is well attached to the surface. Then allow the glue to dry for 24 hours.

Step 5: Hang your wall decoration

Hang your favorite wall decoration using the STAS hooks and cords and admire the result!

Our wooden rails are made out of Ayous wood and are FSC and PEFC certificated. Ayous wood differs from other wood since it does not deform nor splinter, and perfectly suitable to repaint because of its smooth texture. Perfect wood for your picture hanging system! Can be mounted screwed, nailed and glued*.

Experience the pleasant warmth of wood in your interior!

* The bearing capacity of a glued rails is highly dependent on the surface, so care must be taken here. More information on how to best glue our wooden rails can be at the bottom of this page.

STAS wooden rail

Features STAS windsor:
Dimensions: 18 x 45 mm
Length: +/- 240 cm
Material: Ayous wood
Installation: wall mountable, not adjoining to ceiling
Weight capacity: 20 kg/m
Warranty: 5 years

Features STAS riva:
Dimensions: 17 x 45 mm
Length: +/- 240 cm
Material: Ayous wood
Installation: wall mountable, adjoining to ceiling
Weight capacity: 20 kg/m
Warranty: 5 years

STAS windsor & riva have their own collection of hooks, which can be combined with the existing hooks and cords from STAS:
STAS riva: HW50700
STAS windsor:
HW10200 white
HW30200 alu
HW60200 gold

The following hooks and cords can be used in combination with this system:
STAS smartspring on STAS perlon cord with loop (can be loaded up to max. 4 kg)
STAS zipper on STAS perlon cord with loop (can be loaded up to max. 15 kg)
STAS zipper on STAS steel cable with loop (can be loaded up to max. 20 kg)

Download:

Installation manual | Productinfo


Mounting videos : STAS riva mounting with screws and glue



Mounting videos : STAS windsor mounting with screws and glue


5-Step Plan for glueing the STAS riva & STAS windsor

Step 1: Assess the surface

When glueing the STAS wooden rails it’s very important that the surface is well fixed and firm. This goes especially for wall paper. The wall paper must have been applied tightly and evenly to allow the STAS wooden rails to adhere as well as possible.

Step 2: Pick the right glue.

We recommend a glue that is especially designed to offer a very good adhesion on wooden surfaces. We advise you to go see your local DIY store for further recommendations.

Step 3: Pretreatment

Make sure that the surface and the STAS wooden rails are clean, dry, dust- and grease free before you start glueing.

Step 4: Glueing

The glue can best be applied in strokes (so don’t cover the whole rails in glue). Once the glue is applied you can place the STAS wooden rails on its surface (make sure it’s level!). The STAS wooden rails can at this point still be adjusted. When the rails are in the right place you can exert pressure so that the STAS wooden rails is well attached to the surface. Then allow the glue to dry for 24 hours.

Step 5: Hang your wall decoration

Hang your favorite wall decoration using the STAS hooks and cords and admire the result!

Our wooden rails are made out of Ayous wood and are FSC and PEFC certificated. Ayous wood differs from other wood since it does not deform nor splinter, and perfectly suitable to repaint because of its smooth texture. Perfect wood for your picture hanging system! Can be mounted screwed, nailed and glued*.

Experience the pleasant warmth of wood in your interior!

* The bearing capacity of a glued rails is highly dependent on the surface, so care must be taken here. More information on how to best glue our wooden rails can be at the bottom of this page.

STAS wooden rail

Features STAS windsor:
Dimensions: 18 x 45 mm
Length: +/- 240 cm
Material: Ayous wood
Installation: wall mountable, not adjoining to ceiling
Weight capacity: 20 kg/m
Warranty: 5 years

Features STAS riva:
Dimensions: 17 x 45 mm
Length: +/- 240 cm
Material: Ayous wood
Installation: wall mountable, adjoining to ceiling
Weight capacity: 20 kg/m
Warranty: 5 years

STAS windsor & riva have their own collection of hooks, which can be combined with the existing hooks and cords from STAS:
STAS riva: HW50700
STAS windsor:
HW10200 white
HW30200 alu
HW60200 gold

The following hooks and cords can be used in combination with this system:
STAS smartspring on STAS perlon cord with loop (can be loaded up to max. 4 kg)
STAS zipper on STAS perlon cord with loop (can be loaded up to max. 15 kg)
STAS zipper on STAS steel cable with loop (can be loaded up to max. 20 kg)

Download:

Installation manual | Productinfo


Mounting videos : STAS riva mounting with screws and glue



Mounting videos : STAS windsor mounting with screws and glue


5-Step Plan for glueing the STAS riva & STAS windsor

Step 1: Assess the surface

When glueing the STAS wooden rails it’s very important that the surface is well fixed and firm. This goes especially for wall paper. The wall paper must have been applied tightly and evenly to allow the STAS wooden rails to adhere as well as possible.

Step 2: Pick the right glue.

We recommend a glue that is especially designed to offer a very good adhesion on wooden surfaces. We advise you to go see your local DIY store for further recommendations.

Step 3: Pretreatment

Make sure that the surface and the STAS wooden rails are clean, dry, dust- and grease free before you start glueing.

Step 4: Glueing

The glue can best be applied in strokes (so don’t cover the whole rails in glue). Once the glue is applied you can place the STAS wooden rails on its surface (make sure it’s level!). The STAS wooden rails can at this point still be adjusted. When the rails are in the right place you can exert pressure so that the STAS wooden rails is well attached to the surface. Then allow the glue to dry for 24 hours.

Step 5: Hang your wall decoration

Hang your favorite wall decoration using the STAS hooks and cords and admire the result!

Verzending en afhandeling

De verzendkosten bedragen:
€ 4,95 voor Nederland - Gratis levering voor orders vanaf € 75
€ 7,95 voor België - Gratis levering voor orders vanaf € 100.


Op werkdagen voor 1 uur 's middags besteld, zelfde dag verzonden.

Wij versturen onze pakketten met verschillende vervoerders:

DPD (lengtes tot 150 cm).
Transmission (lengtes vanaf 150 cm)
Enkel haken koorden via PostNL

Loading...
Please wait...